Products & Equipment

Accessories.

Beyond forming and shoring systems, FWS stocks the ties, rod, hardware, and release agent every pour depends on. The six families below are our most-ordered items β€” but they’re a starting point, not the whole shelf. Browse the categories below, and see “The Full Scope” further down the page for everything else we carry.Β The bottom line is, if you need it for your concrete pour, we can get it!

πŸ“„ Forming Accessories Handbook (PDF)Β β€” complete general reference and technical information covering ties, anchors, hangers, and safe working loads for forming accessories.

Loop Ties

A46 Loop Panel Tie diagram with A51 Wedge Bolt

Loop panel ties secure and space modular forms: the tie loop sits in the slot between panels, an A51 Wedge Bolt passes through the adjoining form and the loop, and a second Wedge Bolt locks through the first to hold tie and form together. All are available with plastic cones and a water-resistant washer to reduce seepage, and stainless steel versions are available for corrosion resistance.

Load ratings and full specs available on request, or see the Forming Accessories Handbook (PDF).

Snap Ties

A3 Standard Snap Tie diagram showing wall thickness., breakback, and wedge dimensions

Each snap tie is fabricated with flats or crimps to prevent turning in the concrete during breakback, and is available with fixed metal spreader washers and a tight-fitting neoprene water-resistant washer near the tie’s center. Drill plywood holes 1/8β€³ larger than the tie head β€” a 5/8β€³ bit is normally sufficient.

Load ratings and full specs available on request, or see the Forming Accessories Handbook (PDF).

D/R Rod

B12A D/R Thread Bar and B12AD D/R Euro Thread Bar

D/R Thread Bar is a high-strength 15mm and 20mm ductile steel tie rod with a full-length, cold-rolled contour thread β€” 2-1/2 threads per inch for fast installation and stripping. The Euro Thread Bar variant is hot-rolled with two flat sides for self-cleaning and a gripping surface for hand-turning, and is bendable. A full hardware line β€” cast and steel hex nuts, wing nuts, swivel wing nuts, hex couplers, and cast nut washers β€” rounds out the system; double nuts are required to meet full D/R Thread Bar capacity.

Load ratings and full specs available on request, or see the Forming Accessories Handbook (PDF).

D12A Pencil Rod coil and Rod Clamp installation

Pencil Rod

Pencil Rod is a lightweight smooth tie rod used with Rod Clamps or Form Clamps for light wall and footing forming. The D12F Form Clamp is a single, versatile size covering 1/4β€³ to 3/8β€³ rod diameters β€” smooth or deformed β€” and is especially suited to battered or curved wall applications. A D14 Tightening Wrench (1/4β€³) draws the clamp assembly tight for proper seating; it should never be used for straightening forms or pulling rod from set concrete.

Load ratings and full specs available on request, or see theΒ Forming Accessories Handbook (PDF).

Anchor Bolts

F1 Screw Anchor and F2 Screw Anchor Bolt

F1 Screw Anchors and F2 Screw Anchor Bolts are ASTM A307 with skein threads, the most economical re-anchor insert where embedment depth is available β€” the assembled bolt and anchor must be embedded at least ten times the bolt diameter to develop the rated load. 1-3/4β€³ and 2β€³ sizes are available on special order. Caution: the screw anchor bolt is not interchangeable with a Coil Bolt or National Coarse bolt.

Load ratings and full specs available on request, or see theΒ Forming Accessories Handbook (PDF).

Form Release

FWS stocks concrete form release agents to help crews strip cleanly, protect panel face plates, and keep the finished concrete surface free of bugholes and bond failures. Ask your FWS rep for the right release agent for your panel type and pour conditions β€” product-specific coverage rates and technical data sheets are available on request.

The Full Scope

The six families above are just what moves fastest off the shelf. FWS carries the complete forming accessories catalog β€” well beyond what’s broken out into its own page here:

Coil HardwareCoil Bolts, Coil Rod, Adjustable Coil Bolts, Single/Double/Triple Flared Coil Inserts, Coil Loop Inserts, Handle Coil NutsShe-Bolts & Taper TiesD/R Thread Bar She-Bolts, D9 Taper Ties, working parts and form anchorages for medium/heavy formingSpecialty TiesA21 Strap Ties, A7 Spandrel Hook Ties, A9 Tip-to-Tip Ties, A3B1 Combination Ties, A43 Footing TiesRebar & Bracing HardwareB6R Rebar Hooks, D48 Sure-Guard Rebar Protective Caps, D46 Tie Wire, C3 Coil Half HangersScreed & Layout AccessoriesG1 Pipe Holders, G2 Screed Chair Bases, G8 Form Brackets, G27 Round StakesWrenches & Removal ToolsA29 Snap Tie Wrenches, A31 Wrench Head Snap Tie Sockets, A40 Cone Removal Wrenches

Don’t see what you need listed? If it’s a forming accessory, odds are we stock it or can get it fast β€” contact your FWS rep and we’ll track it down.